Notifications about older software probe versions
Dear all, especially software probe hosts, Many of you contribute to RIPE Atlas by running one or more software probes. Thank you for doing so! In the case of software probes you, the host, are in control of the installation and upgrade process. We noticed that there are many probes that have been installed, but not upgraded over time. We'd like to inform you that early next week we'll activate a feature in the system where we'll periodically remind software probe hosts with non-newest versions to upgrade their probes. We expect that at some point later we'll also start enforcing the use of newer versions. Please note that since we provide multiple binary releases, it's also possible to set up automatic package updates for the popular platforms (Debian, RHEL, Raspberry). We'd recommend using this feature (in general, not necessarily just for the probe package). You can find full upgrade instructions for the supported platforms at https://github.com/RIPE-NCC/ripe-atlas-software-probe#upgrading Regards, Robert Kisteleki, for the RIPE Atlas team
On 8 Sep 2026, at 10:54, Robert Kisteleki wrote:
Please note that since we provide multiple binary releases, it's also possible to set up automatic package updates for the popular platforms (Debian, RHEL, Raspberry). We'd recommend using this feature (in general, not necessarily just for the probe package).
You can find full upgrade instructions for the supported platforms at https://github.com/RIPE-NCC/ripe-atlas-software-probe#upgrading
I was hoping to see some hints specifically for Turris Omnia. Perhaps it's not a popular enough platform to be supported? /Niall
On Tue, Sep 8, 2026 at 10:17 AM Niall O'Reilly <niall.oreilly@ucd.ie> wrote:
On 8 Sep 2026, at 10:54, Robert Kisteleki wrote:
Please note that since we provide multiple binary releases, it's also possible to set up automatic package updates for the popular platforms (Debian, RHEL, Raspberry). We'd recommend using this feature (in general, not necessarily just for the probe package).
You can find full upgrade instructions for the supported platforms at https://github.com/RIPE-NCC/ripe-atlas-software-probe#upgrading
I was hoping to see some hints specifically for Turris Omnia. Perhaps it's not a popular enough platform to be supported?
/Niall
Unfortunately we don't have explicit indications if which ones are on Turris (most other platforms give an indication). It's certainly not a large portion of probes at the moment. In any case, I opened a channel to the Turris people to facilitate this upgrade on their platform. Cheers, Robert
Don't you just click a button on the Turris config? el -- Dr. Eberhard W. Lisse \ / Obstetrician & Gynaecologist (retired) el@lisse.NA / * | Telephone: +264 81 124 6733 (cell) PO Box 8421 Bachbrecht \ / If this email is signed with GPG/PGP 10007, Namibia ;____/ Sect 20 of Act No. 4 of 2019 may apply On Sep 9, 2026 at 09:07 +0200, Robert Kisteleki <robert@ripe.net>, wrote:
On Tue, Sep 8, 2026 at 10:17 AM Niall O'Reilly <niall.oreilly@ucd.ie> wrote:
On 8 Sep 2026, at 10:54, Robert Kisteleki wrote:
Please note that since we provide multiple binary releases, it's also possible to set up automatic package updates for the popular platforms (Debian, RHEL, Raspberry). We'd recommend using this feature (in general, not necessarily just for the probe package).
You can find full upgrade instructions for the supported platforms at https://github.com/RIPE-NCC/ripe-atlas-software-probe#upgrading
I was hoping to see some hints specifically for Turris Omnia. Perhaps it's not a popular enough platform to be supported?
/Niall
Unfortunately we don't have explicit indications if which ones are on Turris (most other platforms give an indication). It's certainly not a large portion of probes at the moment.
In any case, I opened a channel to the Turris people to facilitate this upgrade on their platform.
Cheers, Robert
----- To unsubscribe from this mailing list or change your subscription options, please visit: https://mailman.ripe.net/mailman3/lists/ripe-atlas.ripe.net/ As we have migrated to Mailman 3, you will need to create an account with the email matching your subscription before you can change your settings. More details at: https://www.ripe.net/membership/mail/mailman-3-migration/
One click on the reForis Packages page, 10 minutes RTFM, 5 cli commands on the Turris (via ssh), and 1017517 seems to be working. el On 2026/09/09 09:20, Eberhard W Lisse wrote:
Don't you just click a button on the Turris config?
el[...] -- Eberhard W. Lisse \ /Obstetrician & Gynaecologist (retired) el@lisse.NA / * | Telephone: +264 81 124 6733 (cell) PO Box 8421 Bachbrecht\ / If this email is signed with GPG/PGP 10007, Namibia ;____/ Sect 20 of Act No. 4 of 2019 may apply
On 9 Sep 2026, at 10:15, Dr Eberhard W Lisse wrote:
One click on the reForis Packages page, 10 minutes RTFM, 5 cli commands on the Turris (via ssh), and 1017517 seems to be working.
Sure. But the status page for that probe https://atlas.ripe.net/probes/1017517/overview shows FIRMWARE VERSION 5080 (capitals from copy-paste; not my shouting). The page which Robert referenced, which shows instructions for upgrading, indicates that this version should be upgraded, but doesn't give instructions for the Turris platform. Reforis indicates that no update is available. /Niall
Oh, ok, TL;DR :-)-O It'll update itself, eventually :-)-O el -- Dr. Eberhard W. Lisse \ / Obstetrician & Gynaecologist (retired) el@lisse.NA / * | Telephone: +264 81 124 6733 (cell) PO Box 8421 Bachbrecht \ / If this email is signed with GPG/PGP 10007, Namibia ;____/ Sect 20 of Act No. 4 of 2019 may apply On Sep 9, 2026 at 11:35 +0200, Niall O'Reilly <niall.oreilly@ucd.ie>, wrote:
On 9 Sep 2026, at 10:15, Dr Eberhard W Lisse wrote:
One click on the reForis Packages page, 10 minutes RTFM, 5 cli commands on the Turris (via ssh), and 1017517 seems to be working.
Sure. But the status page for that probe https://atlas.ripe.net/probes/1017517/overview shows FIRMWARE VERSION 5080 (capitals from copy-paste; not my shouting).
The page which Robert referenced, which shows instructions for upgrading, indicates that this version should be upgraded, but doesn't give instructions for the Turris platform. Reforis indicates that no update is available.
/Niall
On 9 Sep 2026, at 8:07, Robert Kisteleki wrote:
In any case, I opened a channel to the Turris people to facilitate this upgrade on their platform.
Super! Thanks. /Niall
On 9 Sep 2026, at 8:07, Robert Kisteleki wrote:
In any case, I opened a channel to the Turris people to facilitate this upgrade on their platform.
And they've acknowledged on the Turris Forum that they're working on it. https://forum.turris.cz/t/ripe-atlas-probe-needs-updating/22824 /Niall
Good day We dev team, With recent emails about probe/anchor versions to be up to date, especially the software/virtual probes where the owners/hosts needs to update them “manually”, I went checking to see, but I haven’t found a page with my probes/anchors and their versions, and the “Expected” current/stable/test versions to be updateable too. perhaps also system tags “OldFirmware” and/or “NewFirmwareAvailable” and/or “Stale/oldFirmwre” ? --- On 8 Sep 2026, at 11:54, Robert Kisteleki wrote:
Dear all, especially software probe hosts,
Many of you contribute to RIPE Atlas by running one or more software probes. Thank you for doing so!
In the case of software probes you, the host, are in control of the installation and upgrade process. We noticed that there are many probes that have been installed, but not upgraded over time.
We'd like to inform you that early next week we'll activate a feature in the system where we'll periodically remind software probe hosts with non-newest versions to upgrade their probes. We expect that at some point later we'll also start enforcing the use of newer versions.
Please note that since we provide multiple binary releases, it's also possible to set up automatic package updates for the popular platforms (Debian, RHEL, Raspberry). We'd recommend using this feature (in general, not necessarily just for the probe package).
You can find full upgrade instructions for the supported platforms at https://github.com/RIPE-NCC/ripe-atlas-software-probe#upgrading
Regards, Robert Kisteleki, for the RIPE Atlas team
----- To unsubscribe from this mailing list or change your subscription options, please visit: https://mailman.ripe.net/mailman3/lists/ripe-atlas.ripe.net/ As we have migrated to Mailman 3, you will need to create an account with the email matching your subscription before you can change your settings. More details at: https://www.ripe.net/membership/mail/mailman-3-migration/
participants (5)
-
Dr Eberhard W Lisse -
Eberhard W Lisse
-
Hendrik Visage -
Niall O'Reilly -
Robert Kisteleki