October 2014 - ripe-atlas - mailman.ripe.net

Be careful with probe 4981
by Thomas Holterbach 24 Nov '14

24 Nov '14

Hi, I am going to perform some tests on our atlas probe (id 4981, ASN 3130) during the next two or three weeks. Please note that during this period, measurements from or toward this probe might be inaccurate. Thank you for your attention, Thomas

1 1

Atlas Sagan library and UDP tarceroute results: bug or feature?
by Jen Linkova 18 Nov '14

18 Nov '14

Hello, I've just found that using Sagan library for analyzing UDP traceroute measurement results may produce incorrect results: 'target_responded' variable is not be set to 'True' if the source address of the traceroute reply is not the target address of the traceroute, but any other address that belongs to the node. (From the traceroute.py code: def target_responded(self): if self._target_responded is not None: return self._target_responded self._target_responded = False if self.hops and self.hops[-1].packets: destination_address = IP(self.destination_address) for packet in self.hops[-1].packets: if packet.origin and destination_address == IP(packet.origin): self._target_responded = True return self.target_responded ) I don't think that's a valid assumption that a target node is *always* choosing the probe packet's destination address as a reply source. In particular, in case of UDP packets addressed to anycast, it might fail because the node can reply from another address. In particular, rfc4443 (ICMP for IPv6) says: 2.2. Message Source Address Determination A node that originates an ICMPv6 message has to determine both the Source and Destination IPv6 Addresses in the IPv6 header before calculating the checksum. If the node has more than one unicast address, it MUST choose the Source Address of the message as follows: (a) If the message is a response to a message sent to one of the node's unicast addresses, the Source Address of the reply MUST be that same address. (b) If the message is a response to a message sent to any other address, such as - a multicast group address, - an anycast address implemented by the node, or - a unicast address that does not belong to the node the Source Address of the ICMPv6 packet MUST be a unicast address belonging to the node. == and in the same RFC source address selection for ICMP echo reply messages is defined: The source address of an Echo Reply sent in response to a unicast Echo Request message MUST be the same as the destination address of that Echo Request message. An Echo Reply SHOULD be sent in response to an Echo Request message sent to an IPv6 multicast or anycast address. In this case, the source address of the reply MUST be a unicast address belonging to the interface on which the Echo Request message was received. ==== So, I'm sending this email, first, to warn those of you who is using Sagan to analyze UDP traceroute results, and, secondly, to discuss, if Sagan behavior is a bug (I believe it is) or a feature ;) -- SY, Jen Linkova aka Furry

2 2

Re: [atlas] [mat-wg] New on RIPE Labs: New RIPE Atlas Measurements User Interface
by Steffie Jacob Eravuchira 04 Nov '14

04 Nov '14

Hello, On 10/28/2014 04:25 PM, Mirjam Kuehne wrote: > Dear colleagues, > > We're very excited to announce an all-new user interface for RIPE Atlas > measurements. Users can now schedule, monitor and manage their own > customised measurements more efficiently than ever before, and can now > make use of the tagging feature when selecting probes for use in those > measurements. Learn more about the new features on RIPE Labs and let us > know what you think: > > https://labs.ripe.net/Members/suzanne_taylor_muzzin/ripe-atlas-new-measurem… The new user interface for RIPE Atlas measurements looks well-designed. In the old interface, the "Target" field allows us to choose from a drop-down list of anchors/ringnodes. But in the new interface, the "Target" field is just a text field. Given, as a user, I do not know the hostnames of all anchors, would it be possible to bring the drop-down anchor list feature back? Thanks. -- Regards, Steffie _______________________________________________ Steffie Jacob Eravuchira Research I, Room 91 Computer Networks and Distributed Systems (CNDS) Lab School of Engineering and Sciences Jacobs University Bremen, Germany

6 5

Data Streaming in RIPE Atlas
by Vesna Manojlovic 31 Oct '14

31 Oct '14

Dear colleagues, RIPE Atlas data is now available as a live data stream, opening the door to a host of new applications and use cases. You can read more about this new functionality (and watch the video!) on RIPE Labs: https://labs.ripe.net/Members/suzanne_taylor_muzzin/data-streaming-in-ripe-… Please let us know if you make a cool use of this new feature! Kind regards, Vesna

1 0

MTR measurement support
by Aris Tzermias 31 Oct '14

31 Oct '14

Dear all, I was wondering whether you plan to provide an MTR ( https://en.wikipedia.org/wiki/MTR_%28software%29) support as a User-defined measurement. Best regards,

2 1

SSL error when connecting to https://atlas.ripe.net/
by Gilles Pion 29 Oct '14

29 Oct '14

I'm suddenly unable to connect to https://atlas.ripe.net/ When using Firefox I'm getting the error "ssl_error_no_cypher_overlap" Whith Google Chrome: "ERR_CONNECTION_CLOSED" I'm only able to connect With IE, providing SSLV2 is enabled in advanced options (not a good idea I presume) NB: I'm behind a corporate proxy. -- *Gilles*

5 5

Re: [atlas] Fwd: Your RIPE Atlas Probe (ID: 11513) is now connected to our network
by Rusty Dekema 26 Oct '14

26 Oct '14

Greetings, I do not know anything about probes 14203 or 16058. The only probes I am involved with / responsible for are 10555 and 11513. Cheers, Rusty D On Mon, Oct 20, 2014 at 1:16 AM, Phillip Remaker <remaker(a)gmail.com> wrote: > Thanks for the update! > > Can you give me any insight into #14203 and #16058? > > 16058 is particularly troubling, since it never seems to have come up in > the first place. I have it connected and powered up, with no joy. Is > there any way to fully reset it? > > On Sun, Oct 19, 2014 at 6:49 PM, Rusty Dekema <rdekema(a)gmail.com> wrote: > >> Good evening, >> >> In case you track these sorts of things, the ~2 week disconnection of >> this probe was caused by network trouble on my end (combined with an >> extended vacation), and not by the probe itself or any other part of the >> RIPE Atlas system. >> >> Cheers, >> Rusty Dekema >> >> ---------- Forwarded message ---------- >> From: RIPE Atlas <atlas(a)ripe.net> >> Date: Sun, Oct 19, 2014 at 9:40 PM >> Subject: Your RIPE Atlas Probe (ID: 11513) is now connected to our network >> To: rdekema(a)gmail.com >> >> >> Dear RIPE Atlas probe host, >> >> Thank you for participating in RIPE Atlas! >> >> We're just letting you know that your probe (#11513 with description >> Comcast Business 50/10 (with IPv6 trial).) has re-established its link to >> our network and we are again receiving data from it. For your own records, >> it appears that the reconnection took place at 2014-10-20 01:39 UTC. >> >> If you have any questions, please contact us at atlas(a)ripe.net >> >> Best regards, >> >> RIPE Atlas Team >> >> ********** >> You are receiving this message because you applied for or were given a >> RIPE Atlas probe. We will only send messages when your probe becomes >> disconnected for an extended period of time. >> >> >

1 0

Fwd: [mat-wg] RIPE Atlas Value Proposition Published
by Vesna Manojlovic 24 Oct '14

24 Oct '14

Dear colleagues, please take a look at this news about RIPE Atlas, at mat-wg list. Regards, Vesna -------- Original Message -------- Subject: [mat-wg] RIPE Atlas Value Proposition Published Date: Fri, 24 Oct 2014 15:02:14 +0200 From: Kaveh Ranjbar <kranjbar(a)ripe.net> To: mat-wg(a)ripe.net Dear colleagues, During its meeting in September, the RIPE NCC presented the RIPE NCC Executive Board with a value proposition document detailing the value that RIPE Atlas can bring to network operators, researchers and the Internet community as a whole. The board asked the RIPE NCC to publish this document, which is available on RIPE Labs: https://labs.ripe.net/Members/suzanne_taylor_muzzin/ripe-atlas-value-propos… We also plan to incorporate much of the document's content into the RIPE Atlas website so that RIPE Atlas users can clearly understand the different ways this global Internet measurement network can be used and the many unique benefits it provides. We hope you will find this document useful and that you may even be inspired to make use of RIPE Atlas in new ways. Kind regards, Kaveh Ranjbar Chief Information Officer RIPE NCC

1 0

RIPE 69: Learn More About RIPE Atlas and RIPEstat!
by Vesna Manojlovic 24 Oct '14

24 Oct '14

Dear colleagues, Attending RIPE 69 in London? If so, you can learn more about RIPE Atlas and RIPEstat at our sessions: Tutorial: "Basic RIPE NCC Tools for Network Diagnostics and Monitoring" When: Monday, 3 November 2014, 09:00-11:00 Where: Bourg meeting room, mezzanine floor More information about the RIPE 69 tutorials is available online: https://ripe69.ripe.net/programme/meeting-plan/tutorials/ Workshop: "Advanced Topics in RIPE Atlas Usage" When: Tuesday, 4 November, 18:00–19:00 (date might change!) Where: Side Room More information: https://ripe69.ripe.net/programme/meeting-plan/workshops/ This is an opportunity to exchange experiences, ask questions, and learn from each other. I hope to see you in London! Regards, Vesna

1 0

2Day Telecom LLP (KZ) has joined RIPE Atlas anchors
by Michela Galante 23 Oct '14

23 Oct '14

Dear RIPE Atlas users, We're happy to announce that another RIPE Atlas anchor has joined the network and is now available as a target for probe hosts conducting their own user-defined measurements. The new anchor is called kz-ala-as21299 and it is hosted by 2Day Telecom LLP in Almaty, Kazakhstan. With this anchor we reached a total of 80 online. Anchoring measurements (ping, ping6, traceroute and traceroute6) are scheduled towards this anchor from all the other anchors as well as several hundred probes, providing a continual overview of regional reachability. Results of these measurements are available as raw data in JSON format, and visualised on the map and "seismograph" with many configurable features. You can access the anchoring measurements for all anchors at: https://atlas.ripe.net/anchors/list/ Learn more about RIPE Atlas anchors at: https://atlas.ripe.net/about/anchors/ Thank you for participating in RIPE Atlas! Kind regards, Measurements Community Building Team RIPE NCC mcb(a)ripe.net

1 0